Не могу настроить Wlan

<Linux device driver for Realtek Ethernet controllers>

This is the Linux device driver released for RealTek RTL8168B/8111B, RTL8168C/8111C, RTL8168CP/8111CP, RTL8168D/8111D, RTL8168DP/8111DP, and RTL8168E/8111E Gigabit Ethernet controllers with PCI-Express interface.

<Requirements>

- Kernel source tree (supported Linux kernel 2.6.x and 2.4.x)
- For linux kernel 2.4.x, this driver supports 2.4.20 and latter.
- Compiler/binutils for kernel compilation

<Quick install with proper kernel settings>
Unpack the tarball :
# tar vjxf r8168-8.aaa.bb.tar.bz2

Change to the directory:
# cd r8168-8.aaa.bb

If you are running the target kernel, then you should be able to do :

# ./autorun.sh (as root or with sudo)

You can check whether the driver is loaded by using following commands.

# lsmod | grep r8168
# ifconfig -a

If there is a device name, ethX, shown on the monitor, the linux
driver is loaded. Then, you can use the following command to activate
the ethX.

# ifconfig ethX up

,where X=0,1,2,...

<Set the network related information>
1. Set manually
a. Set the IP address of your machine.

# ifconfig ethX "the IP address of your machine"

b. Set the IP address of DNS.

Insert the following configuration in /etc/resolv.conf.

nameserver "the IP address of DNS"

c. Set the IP address of gateway.

# route add default gw "the IP address of gateway"

2. Set by doing configurations in /etc/sysconfig/network-scripts
/ifcfg-ethX for Redhat and Fedora, or /etc/sysconfig/network
/ifcfg-ethX for SuSE. There are two examples to set network
configurations.

a. Fixed IP address:
DEVICE=eth0
BOOTPROTO=static
ONBOOT=yes
TYPE=ethernet
NETMASK=255.255.255.0
IPADDR=192.168.1.1
GATEWAY=192.168.1.254
BROADCAST=192.168.1.255

b. DHCP:
DEVICE=eth0
BOOTPROTO=dhcp
ONBOOT=yes

<Modify the MAC address>
There are two ways to modify the MAC address of the NIC.
1. Use ifconfig:

# ifconfig ethX hw ether YY:YY:YY:YY:YY:YY

,where X is the device number assigned by Linux kernel, and
YY:YY:YY:YY:YY:YY is the MAC address assigned by the user.

2. Use ip:

# ip link set ethX address YY:YY:YY:YY:YY:YY

,where X is the device number assigned by Linux kernel, and
YY:YY:YY:YY:YY:YY is the MAC address assigned by the user.

<Force Link Status>

1. Force the link status when insert the driver.

If the user is in the path ~/r8168, the link status can be forced
to one of the 5 modes as following command.

# insmod ./src/r8168.ko speed=SPEED_MODE duplex=DUPLEX_MODE autoneg=NWAY_OPTION

,where
SPEED_MODE = 1000 for 1000Mbps
= 100 for 100Mbps
= 10 for 10Mbps
DUPLEX_MODE = 0 for half-duplex
= 1 for full-duplex
NWAY_OPTION = 0 for auto-negotiation off (true force)
= 1 for auto-negotiation on (nway force)
For example:

# insmod ./src/r8168.ko speed=100 duplex=0 autoneg=1

will force PHY to operate in 100Mpbs Half-duplex(nway force).

2. Force the link status by using ethtool.
a. Insert the driver first.
b. Make sure that ethtool exists in /sbin.
c. Force the link status as the following command.

# ethtool -s ethX speed SPEED_MODE duplex DUPLEX_MODE autoneg NWAY_OPTION

,where
SPEED_MODE = 1000 for 1000Mbps
= 100 for 100Mbps
= 10 for 10Mbps
DUPLEX_MODE = half for half-duplex
= full for full-duplex
NWAY_OPTION = off for auto-negotiation off (true force)
= on for auto-negotiation on (nway force)

For example:

# ethtool -s eth0 speed 100 duplex full autoneg on

will force PHY to operate in 100Mpbs Full-duplex(nway force).

<Jumbo Frame>
Transmitting Jumbo Frames, whose packet size is bigger than 1500 bytes, please change mtu by the following command.

# ifconfig ethX mtu MTU

, where X=0,1,2,..., and MTU is configured by user.

RTL8168B/8111B supports Jumbo Frame size up to 4 kBytes.
RTL8168C/8111C and RTL8168CP/8111CP support Jumbo Frame size up to 6 kBytes.
RTL8168D/8111D supports Jumbo Frame size up to 9 kBytes.